Our team is NATE-certified. North American Technician Excellence represents the entire HVAC industry and is an independent, third-party, non-profit organization. NATE-certified technicians are skilled professionals who have verified real working knowledge of HVAC systems through specialized exams. Whether your heating or cooling system requires routine maintenance or complex repair, the NATE-certified team from Nerthling's Heating and Air Conditioning shows up on time, prepared to complete the job quickly and accurately, without unnecessary multiple house calls. We work on all makes and models and offer affordable and convenient service plans to protect your equipment from wear and tear, and ensure like-new performance.
The amount of time air duct cleaning takes can depend on how extensive your duct system is, how old your air ducts are, and whether they have ever been cleaned. On average, expect a standard size home (between 2,000 and 3,000 square feet) to take 2-5 hours for one to two technicians to clean. Here are the proper protocol and equipment you should expect from a professional duct cleaning service, as recommended by the Environmental Protection Agency:
If you’re looking for a professional heating company in Denver with the proper experience to handle your project, our crew has many years of training and experience on most major heating systems available in the Denver area. Our heating company in Denver understands that in some situations, the scope of the damage may put the units beyond repair. In this instance, we can offer you help finding the right energy efficient model that will provide you warmth and savings in your wallet. Heating in Denver can be expensive during the coldest time of year, so choosing the right heating system can give the same amount of heat while at the same time providing big savings when our Denver heater repair technicians help you pick the right system for your home.
At Genz-Ryan, we are here for you 24 hours a day, 7 days a week so you can count on us for all your heating repair work in the Minneapolis area. Our furnace repair technicians are well-trained and experienced. They’re ready to take care of any heating issue that you may have. We are a Lennox Premier Furnace Dealer and provide expert furnace repair service for most of the Minneapolis/St. Paul area. For over 60 years we have been getting the job done right the first time.
If you believe that the ac not working or you’re getting little or no cold air, check these three things first. Make sure all the registers in the house are wide open. Then be sure the furnace filter is clean. Then go outside and clean off the condenser coils (Photo 2). If several registers were closed or the filter was clogged, the reduced airflow could have caused the evaporator coil to ice up and stop cooling your home. If you’ve changed the filter and opened all the registers and you’re still not getting airflow at the registers, deice the A-coil. Move the thermostat mode switch from “Cooling” to “Off” and move the fan switch from “Auto” to “On.” Let the blower run for at least 30 minutes or until there’s good airflow at the registers. Then turn the AC back on to test it. If it works for the next 12 hours, you’ve solved the problem.
Welzig Heating & Air is on call, 24 hours a day, 365 days, making sure that the skilled assistance you need is always available. There’s no need to struggle with decreased performance from your air conditioner. Even small aggravations, such as elevated sound levels, strange smells, or longer running times, are warning signs of larger issues and usually add up to higher running costs. When you trust your cooling equipment to Welzig Heating & Air, we work to not only resolve pressing issues. but ensure reliability, efficiency, and longevity. A thorough inspection often protects against degraded air quality, property damage, and premature system failure. We work on all makes and models of air conditioners, and with every repair we tackle, our team of dedicated technicians earn your satisfaction. Through exemplary customer service, ethical business practices, and exacting standards, Welzig Heating & Air provides superior solutions to homeowners across Boulder, Longmont, Louisville, Lafayette, CO & more.
High-efficiency condensing furnaces (90% AFUE and above) are a bit more complex than conventional furnaces. The main differences between a conventional and condensing furnace are the heat exchanger technology used to extract heat from the combustion process and the method used to exhaust the combustion gases. In these ways, the furnaces are very different. The condensing furnace does not have a significantly more efficient combustion process than does a conventional furnace; both use gas burners with electronic ignition. The difference lies in that the condensing furnace has a more efficient heat extraction process after combustion.
If the condenser coils are clogged, the compressor can overheat and shut down. You’ll experience intermittent periods of minimal cooling, followed by no cooling. Even if you’re “sure” the condenser coils are clean, clean them again. Turn off the power. Flip the air conditioning service and furnace circuit breakers in your main electrical panel to the “Off” position. Next, turn off the power switch right at the furnace or air handler. Then yank the disconnect block (Photo 1) and clean the condenser coils (Photo 2). If the air conditioning service still doesn’t work properly after you’ve cleaned the condenser coils, installed a new filter and opened all the supply vents, proceed with the following repairs.
We have strived extremely hard to become the premier HVAC repair & installation choice for the peole of Columbia, Maryland. We pride ourselves on being the first HVAC company in all of Maryland to be awarded with Factory Authorized status. We have also earned the Distinguished Dealer Award by the Carrier Corporation for our strong & consistent dedication to superior local heating and air conditioning work in addition to exceptional customer satisfaction.
Inspect your furnace thermostat by first making sure that it’s turned on. Also, ensure that the thermostat switch is turned to “heat” and not “cool”. If your furnace will still not start with the thermostat on, try adjusting the temperature settings to a few degrees higher. Inspect any visible wires for breaks or splits, and make sure your thermostat batteries are not dead. Do not touch any open wires; contact a professional.
2Be sure the furnace’s circuit breaker is on or that its fuse has not blown. Check both the main electrical panel and any secondary subpanels that supply power to the unit. If the circuit has blown or tripped, reset the circuit breaker by flipping it all the way off and then on again. Or replace the fuse. If the circuit blows again, there is probably a short in the electrical system providing power to the furnace. For this, you may need to call an electrical contractor.
Repair Clinic’s gas furnace troubleshooting guide will walk you through the steps necessary for diagnosing your furnace problem. Start with our list of symptoms. When you find the right one, we’ll show you the common causes. Enter your model number into the search field and you’ll know which part to buy. We can even show you how to install it. Where else can you find online furnace troubleshooting help like this?
Has another company told you that your furnace has a cracked heat exchanger? The heat exchanger is the heart of your furnace. Its failure can result in a dangerous situation for your home and the best solution is usually a new furnace. Because of these issues, Bonney takes this situation very seriously. We will offer you proof of the cracked heat exchanger in the form of a picture from our video inspection camera or a report from our exhaust gas analyzer, before we make our recommendation.
Our technicians explain all of your options before beginning the repair, so you can decide whether a repair or replacement is best for you. Our No Surprises Pricing—including charging by the job, not by the hour—means the price we quote you is the price you pay. If you decide that replacing your furnace is the best course of action, we can install a new, high-efficiency model in its place.
As a Bryant® dealer, with a wide variety of products to choose from, we can keep your family healthy and feeling comfortable all year long. We carry a complete line of indoor comfort equipment with innovations that raise the standards of comfort and reliability, including air conditioners, heat pumps, gas furnaces, programmable thermostats, humidifiers, ductless split systems, geothermal systems, boilers, air cleaners, ultra violet lights, ventilators and zoning products. Let the experts at Moab Heat - N - Cool help you customize a solution that's right for you.