When it comes to heater repair in Denver, a properly serviced system means significant savings for the homeowner. When a Denver heating technician inspects your system before the winter sets in, the first thing they will check is the condition of the air filters. These filters are important, because they are responsible for removing contaminants, allergens, and dust particles from the air every time the system is turned on. When the filters are clogged, expect more particles to easily pass through right into the air you breathe inside the home. The Denver heating experts will inspect and replace any filters that are no longer effective.
What happens when you have an emergency? The first reaction of most people is to panic. When a furnace stops working, you need it fixed and fixed immediately—especially in the middle of a cold, Ohio winter. That need can make people feel as if they are at the mercy of the repair company. That is why it is so important to call a company you can trust and rely on—Jennings Heating and Cooling.
If your furnace has a pilot light, look for the flame. Check your owner’s manual or the instructions posted inside the furnace cabinet for step-by-step lighting instructions. Usually this involves first turning the gas valve to Off and waiting a couple of minutes. Then you turn it to Pilot. Next, press and hold it down while you light the flame. Last, wait a minute or so, release it, and then turn it to On.
This job involves removing the access panel, loosening a couple of bolts that hold the blower motor at the proper tension, and adjusting its distance or realigning the belt. In many cases, it’s a good idea to remove the belt and buy a replacement at a home center. Last, when reinstalling the belt, be careful not to over-tighten it; this can wear out the motor bearings.
In order to get the most out of your equipment, we highly recommend proper preventative HVAC maintenance. You’ll want to make sure from the outset that you have access to skilled and knowledgeable technicians who have been factory-trained to service your particular model, since different systems require different highly specific modifications. It’s advisable to find a reputable HVAC dealer in the Atlanta area that guarantees their work and offers annual service contracts to their customers to ensure necessary seasonal maintenance is always being performed regularly. Many times, timely adjustments and filter changes that are done on a regular basis can wind up saving you from breakdowns that always seem to occur right when you need your system the most.

The thermocouple is a copper rod that the pilot flame heats-up. When it gets hot enough, the thermocouple signals that there is enough heat to burn the gas fuel being released into the appliance—and so it allows the gas to be released to the burners. In some cases where the pilot light won’t stay lit, the thermocouple needs to be adjusted or replaced. This is generally a job for a professional.
AC units and thermostats have built-in delay features when they’re shut down and then repowered. The delay can be as long as 10 minutes. And, if you’ve subscribed to an energy-saving device from your local power utility, the unit can take even longer to reset. If you’ve installed the parts shown and reinstalled the disconnect block, repowered the circuit breaker, turned on the switch at the furnace, moved the thermostat to AC mode and lowered the temperature below the indoor temperature, and the unit doesn’t fire up after 30 minutes, it’s time to call a pro.

Our Aurora furnace repair company only employs the highest quality professionals. We realize that dealing with a furnace is very serious, and we only have workers that are highly experienced in doing so. In order to deal with the best company that specializes in furnace replacement in Aurora and furnace repair in Aurora, you have to be sure that the company is professional and committed to a quality customer service experience.
Central home air conditioner service systems consist of two major components: a condensing unit that sits outside your house, and the evaporator coil (often referred to as an A-coil) that sits in the plenum of your furnace or air handler. The refrigerant in the A-coil picks up the heat from your home and moves it to the outdoor condensing unit. The condensing unit fan blows outside air through the condensing coil to remove the heat. The condensing unit houses the three parts replaceable by a DIYer: the contactor, the start/run capacitor(s) and the condenser fan motor. The condensing unit also houses the compressor, but only a pro can replace that. The A-coil has no parts that can be serviced by a DIYer.

HVAC Repair

×