The cost to replace your gas furnace will vary based on the type and size of furnace you select, labor and installation costs, and any repairs your HVAC system may need. Nationally, average HVAC prices for a heating specialist range between $1,800 and $2,500. It’s important to select the right size gas furnace for your heating needs. A furnace that’s too small won’t heat your house properly, while a furnace that’s too large will run inefficiently, cycling on and off and likely breaking down sooner. HVAC specialists calculate your exact heat needs by measuring your home and incorporating variables such as the regional climate and your home’s level of insulation. Retail pricing for gas furnaces can range from $650 up to $3,000 and more. The higher the AFUE (annual fuel utilization efficiency) rating of the furnace, the more efficient it is at turning fuel into heat and the lower your carbon footprint and utility bill will be. HVAC installation costs are often based on an hourly rate and can range from under $50 to over $100 per hour, depending on the company and the furnace being installed. Higher-end furnaces cost more to install because they require added labor and expertise. For a typical installation, it might take two HVAC installation pros one day or less to remove your old furnace and replace it with a new one.

HVAC Repair Company


The contactor (relay) and start/run capacitor(s) (see illustration below) fail most often and are inexpensive. So it’s a safe bet to buy and install those parts right away, especially if your air conditioning service unit is older than five years. The condenser fan motor can also fail, but it runs about $150 — hold off buying that unless you’re sure that’s the culprit.
Many things can go wrong with your furnace, all of which should be repaired and examined by experienced professionals. Trust Randazzo Heating, Cooling, and Fireplaces to repair and help you maintain your furnace*. We value our customers and their decisions, so we will always be honest and explain the best possible solution for you. Contact us today so we can help you out! Click Here for our warranty policy.
You can usually slip the belt on the motor’s (smaller) pulley first and then start it on the blower pulley. Rotate the blower pulley by hand, holding the belt in place but keeping your fingers from getting caught between the belt and the pulley. The belt should slip right into place. If it seems to be too tight or difficult to set in place, it may be necessary to adjust the motor mount to provide more slack.

Consequently, this water must exit the air handler—typically through plastic pipe or a drain tube. That drain tube goes directly outside, often terminating near the compressor, or to a floor drain or to a small electric “condensate pump” located by the air handler. Where a condensate pump is used, it connects to a 1/2-inch vinyl or rubber tube that exits outdoors or to a drain.

An improperly maintained heating and air conditioning is an inefficient heating and air conditioning system. That’s why we provide appointments for annual inspections with our licensed technicians. It’s our goal to make sure that your home is as comfortable and energy-efficient as possible. For inspections, repairs, and service, contact BGE HOME for quality service.


Advice you can count on – When you have an emergency, you are not always in the position of asking questions to determine if the repairs you are receiving are what you need. At Jennings, our NATE Certified technicians will walk you through the repairs and explain why you need them. You can trust that everyone on Jennings’ staff will give you honest advice.

The amount of time air duct cleaning takes can depend on how extensive your duct system is, how old your air ducts are, and whether they have ever been cleaned. On average, expect a standard size home (between 2,000 and 3,000 square feet) to take 2-5 hours for one to two technicians to clean. Here are the proper protocol and equipment you should expect from a professional duct cleaning service, as recommended by the Environmental Protection Agency:
"Jorge Mondragon did a fantastic job installing a new upstairs AC and furnace. His price was close to the best that I received, and after seeing the positive reviews on Thumbtack, I decided to give him the job. He came in with two other crewman and worked about a half day to get the job done. They used tarps on the floor and covered the entire section they walked on during the install, including the stairs. The new AC works great, although the real test will come when the brutal summer kicks in. I'll update my review once I have a few months on the unit. The install job looked thorough and well done. Professional, polite, well-spoken, and hardworking. This is my go-to company for all future HVAC needs and I'll be recommending him to everyone I know."
Remember the way service used to be? Remember when a company did what it promised? Remember when service people gave service? They still do at Coomes Air Conditioning & Heating. Our technicians are polite, clean, and well groomed. Our technicians will show up when promised and clean up before they leave. They will take the time to explain things to you and offer you options. And, they will do the job right, the first time, every time. Call Coomes Air Conditioning & Heating today.
The cost to replace your gas furnace will vary based on the type and size of furnace you select, labor and installation costs, and any repairs your HVAC system may need. Nationally, average HVAC prices for a heating specialist range between $1,800 and $2,500. It’s important to select the right size gas furnace for your heating needs. A furnace that’s too small won’t heat your house properly, while a furnace that’s too large will run inefficiently, cycling on and off and likely breaking down sooner. HVAC specialists calculate your exact heat needs by measuring your home and incorporating variables such as the regional climate and your home’s level of insulation. Retail pricing for gas furnaces can range from $650 up to $3,000 and more. The higher the AFUE (annual fuel utilization efficiency) rating of the furnace, the more efficient it is at turning fuel into heat and the lower your carbon footprint and utility bill will be. HVAC installation costs are often based on an hourly rate and can range from under $50 to over $100 per hour, depending on the company and the furnace being installed. Higher-end furnaces cost more to install because they require added labor and expertise. For a typical installation, it might take two HVAC installation pros one day or less to remove your old furnace and replace it with a new one.
Mitsubishi Electric is a world leader in air conditioning systems for residential, commercial and industrial use. Challenged to create air conditioning systems that provide exemplary performance in the wide-ranging climatic conditions found throughout Japan, our engineers develop amazingly sophisticated yet durable units and systems capable of constant use under virtually any natural climatic condition on earth.

Our technicians explain all of your options before beginning the repair, so you can decide whether a repair or replacement is best for you. Our No Surprises Pricing—including charging by the job, not by the hour—means the price we quote you is the price you pay. If you decide that replacing your furnace is the best course of action, we can install a new, high-efficiency model in its place.
At BGE HOME, our customers trust our courteous and knowledgeable technicians to repair the most sophisticated heating and air conditioning system breakdowns. Every BGE HOME technician is licensed in their trade and adheres to a stringent in-house certification program that guarantees their knowledge, affirms their commitment to the customer, and ensures excellence in completing every heating and air conditioning repair with the highest level of quality.
Saving you money – When you have an emergency furnace repair, one concern that comes to mind is how much it will cost to repair your furnace. Many companies will charge an additional fee to come to your home in the middle of the night or on the weekend. That’s not us. We never charge an emergency fee. Keeping your repair costs affordable is of utmost importance to us.

So the furnace went out (again). We’re probably not the people you want to be dialing, but in these circumstances, Service Experts Heating & Air Conditioning in North America should be your very first call. You don’t even have to worry how late (or early) it is – our NATE-certified technicians available at all hours, every day of the year. We’ll be there in a jiffy and get the job done fast – so you can get back to your routine and not have to even think about needing another furnace repair anytime soon.
As a Carrier® dealer, with a wide variety of products to choose from, we can keep your family healthy and feeling comfortable all year long. We carry a complete line of indoor comfort equipment with innovations that raise the standards of comfort and reliability, including air conditioners, heat pumps, gas furnaces, programmable thermostats, humidifiers, ductless split systems, geothermal systems, boilers, air cleaners, ultra violet lights, ventilators and zoning products. Let the experts at Dunes Heating and Air Conditioning, LLC help you customize a solution that's right for you.
Air Blue Heating and Cooling Inc. provides a full range of residential and commercial heating, cooling, and air quality services across Chicagoland and the surrounding suburbs.  With over thirty years of practical experience, we know exactly how to protect your comfort, wallet, and enjoyment of your indoor space.  As a Carrier Factory Authorized Dealer, we ensure top quality products and maximize performance through skilled services.  Our team is fully licensed, bonded, insured, and factory trained.  Every call is answered by a NATE-certified professional, who has verified technical excellence through strenuous, industry-recognized exams.
No one wants to be stuck in the dead of summer with a broken air conditioner, or in the cold of winter with a broken furnace or boiler. That’s why we’re available any time of day to make your emergency heating and air conditioning repair and get your system up and running as quickly as possible. We’ll show up on time, in uniform and ready to make your HVAC repair right the first time.
For more than sixty years, Nerthling's Heating and Air Conditioning has continued a tradition of superior customer service across Erie County, including Erie, Millcreek and Fairview.  Family owned and operated, we treat you, your home, and your comfort the way we would like to be treated.  This commitment to integrity extends to every service and product we provide.  Our goal is to deliver the highest rewards for your investment, whether you require installation, maintenance, or repair.  We offer a wide range of styles and sizes of equipment, services, and resources to help you achieve your goals for temperature control, air quality, and energy savings.
High-efficiency condensing furnaces (90% AFUE and above) are a bit more complex than conventional furnaces. The main differences between a conventional and condensing furnace are the heat exchanger technology used to extract heat from the combustion process and the method used to exhaust the combustion gases. In these ways, the furnaces are very different. The condensing furnace does not have a significantly more efficient combustion process than does a conventional furnace; both use gas burners with electronic ignition. The difference lies in that the condensing furnace has a more efficient heat extraction process after combustion.
As one of the premier heating & cooling companies in St. Louis, Vogel has dedicated our business to serving our customers with the utmost quality in HVAC services for both residential and commercial entities alike. We strive to build out a culture within our team that delivers the kind of experience you deserve when working with a service provider. The qualities that are most important to you, are most important to us - convenience, trustworthiness, good value, impeccable quality, and our willingness to stand behind our successes and learn from our mistakes. We invite you to explore our site, see what customers say, and give us a call.
Furnaces and thermostats are not mix-and-match appliances. Using the wrong type of thermostat with a furnace will cause operating problems and can be dangerous. Although thermostats look similar, they are designed very differently. There are numerous types of heating systems and thermostat systems and they need to be coordinated for safe and proper operation. There are three types of thermostat systems used today: millivoltage, low voltage, and line voltage.​
To keep your furnace in good working order it’s important to have it regularly cleaned. The national average furnace cleaning cost ranges from $60 to $80, though prices can vary greatly based on where you live in the country and what your furnace maintenance includes. An HVAC company may have different rates for different levels of furnace maintenance. For example,one company may offer general furnace maintenance for $79 and advanced maintenance for $138. Another company may offer a 38-point maintenance check for $89 and a 64-point maintenance check for $178. According to Energy.gov, a standard furnace cleaning and maintenance visit can include:
×